S-Plan · 9 parts · 27 wires
Wireless S-Plan wiring diagram
In short
An S-Plan is a fully pumped heating system with two 2-port motorised zone valves, one for central heating and one for hot water, driven by a programmer, a room thermostat and a cylinder thermostat. Each valve’s end switch feeds the boiler’s switched live, so the boiler fires only while a valve is open: the boiler interlock.
A working Wireless S-Plan in the simulator. Wire colours follow BS 7671; every terminal is live, neutral, earth or dead, and the meter reads what the circuit is doing.
Wiring centre numbering
The numbering is a convention so that the next engineer can read your work. A block carries whatever you land on it; the test harness proves the same system wired on scrambled blocks.
| Block | Carries |
|---|---|
| 1 | Permanent live from the fused spur (brown) |
| 2 | Neutral (blue) |
| 3 | Earth (green/yellow) |
| 4 | CH ON from the programmer, out to the room thermostat L |
| 5 | Room thermostat call, out to the heating valve brown |
| 6 | HW ON from the programmer, out to the cylinder thermostat C |
| 7 | Spare on an S-Plan |
| 8 | Cylinder thermostat call, out to the hot water valve brown |
| 9 | Spare |
| 10 | Both valve oranges in, boiler switched live out |
| 11 | Spare |
| 12 | Spare |
Every wire, terminal by terminal (27)
| # | From | Terminal | To | Terminal | Colour |
|---|---|---|---|---|---|
| 1 | Heat-Only Boiler | PL | Circulation Pump | L | Grey |
| 2 | Heat-Only Boiler | E | Wiring Centre | 3 | Green/yellow (earth) |
| 3 | 2-Port Valve (hot water) | E | Wiring Centre | 3 | Green/yellow (earth) |
| 4 | Fused Spur | E | Wiring Centre | 3 | Green/yellow (earth) |
| 5 | Fused Spur | N | Wiring Centre | 2 | Blue (neutral) |
| 6 | Circulation Pump | N | Wiring Centre | 2 | Blue (neutral) |
| 7 | Heat-Only Boiler | N | Wiring Centre | 2 | Blue (neutral) |
| 8 | 2-Port Valve (hot water) | N | Wiring Centre | 2 | Blue (neutral) |
| 9 | Fused Spur | L | Wiring Centre | 1 | Brown (live) |
| 10 | Heat-Only Boiler | L | Wiring Centre | 1 | Brown (live) |
| 11 | 2-Port Valve (hot water) | O | Wiring Centre | 10 | Orange |
| 12 | Cylinder Thermostat | C | Wiring Centre | 6 | Brown (live) |
| 13 | 2-Port Valve (hot water) | B | Wiring Centre | 8 | Brown (live) |
| 14 | 2-Port Valve (hot water) | G | Wiring Centre | 1 | Grey |
| 15 | Circulation Pump | E | Wiring Centre | 3 | Green/yellow (earth) |
| 16 | Heat-Only Boiler | SL | Wiring Centre | 10 | Orange |
| 17 | Wiring Centre | 8 | Cylinder Thermostat | 1 | Grey |
| 18 | 2-Port Valve (heating) | B | Wiring Centre | 5 | Brown (live) |
| 19 | 2-Port Valve (heating) | G | Wiring Centre | 1 | Grey |
| 20 | 2-Port Valve (heating) | O | Wiring Centre | 10 | Orange |
| 21 | 2-Port Valve (heating) | E | Wiring Centre | 3 | Green/yellow (earth) |
| 22 | 2-Port Valve (heating) | N | Wiring Centre | 2 | Blue (neutral) |
| 23 | Wireless Receiver 2Ch | E | Wiring Centre | 3 | Green/yellow (earth) |
| 24 | Wireless Receiver 2Ch | L | Wiring Centre | 1 | Brown (live) |
| 25 | Wireless Receiver 2Ch | N | Wiring Centre | 2 | Blue (neutral) |
| 26 | Wireless Receiver 2Ch | 4 | Wiring Centre | 5 | Grey |
| 27 | Wiring Centre | 6 | Wireless Receiver 2Ch | 3 | Grey |
The truth table it must pass
Commissioning is four demand states and four results. The test harness runs this table against the circuit before every release.
| Demand | Result |
|---|---|
| No demand: programmer HW off and CH off (room stat calling, cylinder cold) | Both valves stay closed; boiler off |
| CH only: programmer CH on (room stat calling, cylinder cold) | Heating valve opens, hot water valve stays closed; boiler fires and the pump runs |
| HW only: programmer HW on (room stat calling, cylinder cold) | Hot water valve opens, heating valve stays closed; boiler fires and the pump runs |
| CH + HW: programmer HW on and CH on (room stat calling, cylinder cold) | Both valves open; boiler fires and the pump runs |
| Programmer HW on and CH on, both stats satisfied | Both valves closed; boiler off |
Related
Build it lesson by lesson
- S-Plan Wiring course
Wire a complete S-Plan heating system step-by-step. Each connection is validated as you build a fully working system.
Other systems
If this is your home: this page is written for heating engineers. Mains wiring and gas appliances are not DIY jobs; call a Gas Safe registered engineer. If you smell gas, leave the building and call the National Gas Emergency Service on 0800 111 999.
Your first fault is waiting.
The demo opens with the launch: leave your email and the link lands in your inbox that day.